Midas DL371 Especificações Página 57
- Página / 104
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
About the patching procedure 37
PRO3 Control Centre
Quick Reference Guide
>> To access the Patching screen
Do one of the following:
• At the GUI, choose home
Patching.
• Press the patching/metering button in the primary navigation zone.
• At the GUI, click a src (source) or dest (destination) button. The Patching screen
will open at the appropriate tab/configuration window.
About the patching procedure
Although patching can be thought of as routing/rerouting the control centre’s incoming,
internal and outgoing signals, in the context of the Patching screen, patching also
encompasses the setting up and configuration of the stage and FOH rack I/O devices.
The patching procedure is initially carried out after system installation and comprises:
• Device configuration Configure the devices by adjusting their parameters (see
below).
• Snake selection Configure the control centre according to the type of ‘snake’ you
are using for the X and Y networks (see “Configuring the snake type” on page 39).
This is important, as the control centre will not work unless the snake type
is correctly configured.
• Setting up the I/O rack devices Set up the system devices, such as line I/O,
DN9696 and generic AES50, in the I/O tabs in the From and To sections of the
Patching screen (see “Setting up the I/O rack devices” on page 39).
• Patching Carry out all of the required routing, for example, mics to input channels
(see “How to patch” on page 41).
Configuring the devices
You have the option to configure the devices from the Patching screen. Parameters,
such as gain and +48V phantom voltage, can be adjusted or switched on/off,
respectively, via a device-specific configuration window.
These configuration settings can be independent of channel data, as (until patched)
they only control the physical unit. If a device is subsequently patched to one or more
channels, the channel(s) control the device, and vice-versa.
The device configuration area also allows control of audio parameters when the device
is used as a direct connection to another device. For example, FOH to stage via a
digital snake, instead of through the DSP. In this case the settings are also saved in the
show file and can be automated, even though the signals are not routed through the
control centre DSP.
Device configuration procedure
Although the procedure for configuring the devices is similar, their parameters are
dependent on device type. The procedure for configuring the devices of a similar type
involves:
• Opening the configuration window of the device.
• Selecting one of the device’s cards/channel ranges and configuring the available
parameters.
• Repeating for the other cards/channel ranges of the device.
• Repeating for the other devices.
• Closing the device’s configuration window.
- PRO3 Control Centre 1
- Quick Reference Guide 1
- IMPORTANT SAFETY INSTRUCTIONS 3
- EC-Declaration of Conformity 5
- Licences 7
- Precautions 11
- Optional equipment 13
- Special accessories 13
- Electric fields 13
- Safety equipment 13
- Recommandations 15
- Recommandations xvii 17
- Contents 19
- Appendices 20
- Overview 21
- Chapter 1: Introduction 23
- 4 Chapter 1: Introduction 24
- Service and support 24
- Introducing the PRO3 25
- Applications 26
- System components 27
- Bay and GUI layout 30
- Control surface 11 31
- Operation 35
- Chapter 4: Before You Start 37
- Hints and tips 38
- Saving your work 39
- About channel operation 41
- About GUI operation 41
- 2 Do one of the following: 42
- Using the GUI menu 43
- Text editing 44
- Chapter 6: Navigation 45
- 26 Chapter 6: Navigation 46
- 28 Chapter 6: Navigation 48
- Navigating the mix buses 49
- 30 Chapter 6: Navigation 50
- 32 Chapter 6: Navigation 52
- Navigation via the GUI 53
- 34 Chapter 6: Navigation 54
- Chapter 7: Patching 55
- 36 Chapter 7: Patching 56
- About the patching procedure 57
- Configuring the devices 57
- 38 Chapter 7: Patching 58
- Configuring the snake type 59
- 40 Chapter 7: Patching 60
- How to patch 61
- 42 Chapter 7: Patching 62
- Chapter 8: Basic Operation 63
- 44 Chapter 8: Basic Operation 64
- Input equalisation (E zone) 65
- 46 Chapter 8: Basic Operation 66
- Output processing 67
- 48 Chapter 8: Basic Operation 68
- Using VCA/POP groups 68
- Configuring VCA/POP groups 69
- Control GroupsGroup Sheet 69
- 50 Chapter 8: Basic Operation 70
- Setting up a mix 70
- Setting up a mix 51 71
- 52 Chapter 8: Basic Operation 72
- Using fader flip 72
- Setting up the effects rack 73
- 54 Chapter 8: Basic Operation 74
- 56 Chapter 8: Basic Operation 76
- 1 Click LOAD 77
- 58 Chapter 8: Basic Operation 78
- 1 Click STORE SCENE 79
- 4 Do one of the following: 79
- 60 Chapter 8: Basic Operation 80
- 62 Chapter 8: Basic Operation 82
- Using copy and paste 82
- User library (presets) 83
- 64 Chapter 8: Basic Operation 84
- Surround panning 84
- 12 3 4 56 85
- 66 Chapter 8: Basic Operation 86
- Two-man operation 86
- 68 Chapter 8: Basic Operation 88
- Security (locking mode) 88
- Connecting And 89
- Setting Up The 89
- Initial set-up procedure 91
- Unpacking the equipment 91
- Making up a rack 91
- Wiring instructions 91
- Mix position 92
- Powering the system 93
- Appendix A: Troubleshooting 100
- Swapping the active network 101
- 2 Click FILE SYNC 102
- © 2010 Red Chip Company Ltd 104
Manuais e produtos relacionados com Motor Midas DL371
Motor Midas DL371 Especificações
(30 páginas)
(30 páginas)
Metrohm 794 Basic Titrino manuály
Uživatelské manuály a uživatelské příručky pro Zařízení Metrohm 794 Basic Titrino.
Poskytujeme 3 manuály pdf Metrohm 794 Basic Titrino ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais